Hi guys,
i have issue to connect my rigs to prohashing server. have tried to use this commands via claymore:
EthDcrMiner64.exe -epool stratum+tcp://prohashing.com:3339 -ewal myPHlogin -epsw n=rig1 -allcoins 1 -allpools 1 -platform 1
also tried many variations and still gettign same error message.
ETH: Stratum - Connected (prohashing.com:3339) (unsecure)
ETH: Authorization failed
: {"id":2,"result":null,"error":[-3,"Method'eth_submitLogin'notfoundforservice'mining'",null]}
ETH: Job timeout, disconnect, retry in 20 sec...
any advice?
thanks
Ehash/claymore rig setup
Forum rules
Welcome to the mining rig and connectivity support forum!
This forum is for discussing issues with mining rigs and connectivity issues with experienced PROHASHING miners. This is a great place to ask questions about connecting specific hardware to PROHASHING.
Remember, PROHASHING employees do not closely monitor the forums like we do the official support channels, so this forum's purpose is to connect you with other PROHASHING miners who have experience with similar hardware/issues. If you have connectivity issues you are unable to resolve here on the forum, please submit a ticket through the official support channels.
For the full list of PROHASHING forums rules, please visit https://prohashing.com/help/prohashing- ... rms-forums.
Welcome to the mining rig and connectivity support forum!
This forum is for discussing issues with mining rigs and connectivity issues with experienced PROHASHING miners. This is a great place to ask questions about connecting specific hardware to PROHASHING.
Remember, PROHASHING employees do not closely monitor the forums like we do the official support channels, so this forum's purpose is to connect you with other PROHASHING miners who have experience with similar hardware/issues. If you have connectivity issues you are unable to resolve here on the forum, please submit a ticket through the official support channels.
For the full list of PROHASHING forums rules, please visit https://prohashing.com/help/prohashing- ... rms-forums.
Re: Ehash/claymore rig setup
What happens if you just try:
EthDcrMiner64.exe -epool stratum+tcp://prohashing.com:3339 -ewal myPHlogin -epsw n=rig1
without the other parameters?
and I am guessing the myPHlogin is the username you use on the prohashing.com site not here on the forums.
EthDcrMiner64.exe -epool stratum+tcp://prohashing.com:3339 -ewal myPHlogin -epsw n=rig1
without the other parameters?
and I am guessing the myPHlogin is the username you use on the prohashing.com site not here on the forums.
Re: Ehash/claymore rig setup
i have already tried this option with same results and yes i have two username and tried both, of course first was on webpage not the forum.
-
Steve Sokolowski
- Posts: 4585
- Joined: Wed Aug 27, 2014 3:27 pm
- Location: State College, PA
Re: Ehash/claymore rig setup
We use the "NiceHash stratum" protocol. There is an older "getWork" protocol which we don't support. The command that works for me is:keksik wrote:Hi guys,
i have issue to connect my rigs to prohashing server. have tried to use this commands via claymore:
EthDcrMiner64.exe -epool stratum+tcp://prohashing.com:3339 -ewal myPHlogin -epsw n=rig1 -allcoins 1 -allpools 1 -platform 1
also tried many variations and still gettign same error message.
ETH: Stratum - Connected (prohashing.com:3339) (unsecure)
ETH: Authorization failed
: {"id":2,"result":null,"error":[-3,"Method'eth_submitLogin'notfoundforservice'mining'",null]}
ETH: Job timeout, disconnect, retry in 20 sec...
any advice?
thanks
EthDcrMiner64.exe -epool stratum+tcp://prohashing.com:3339 -esm 3 -ewal testuser1 -allpools 1
Re: Ehash/claymore rig setup
Finally i can confirm with above config im able to mine without any issue. also can add more parameters, such as:
-platform 1 -mode 1 -epsw rig1. I have not tried any others,but it should be working as well.
-platform 1 -mode 1 -epsw rig1. I have not tried any others,but it should be working as well.
Re: Ehash/claymore rig setup
Anyone tried configuring an Bitmain E3 to work?
Re: Ehash/claymore rig setup
I tried for hours, both direct and through a proxy. I've given up.citronick wrote:Anyone tried configuring an Bitmain E3 to work?
Either it just shows up dead and stays that way, or, thru MRR I can get some settings to work, but it never shows a hashrate (through the MRR console). On PH, it just creates hundreds of ghost miners, never stays connected long enough to show a hashrate.
Anyone get the E3 to work here?
Re: Ehash/claymore rig setup
Steve said that Nicehash stratum is currently supported - which is -esm 3 Claymore speak.
I think we need get work type mining support like ethminer - perhaps PH can consider adding this support.
https://github.com/ethereum-mining/ethminer
That will get most miners using Claymore and non-Claymore miners out there... I think there is no dev fee in ethminer
If X3 cant work with NH, I have little confidence E3 can work....
I think we need get work type mining support like ethminer - perhaps PH can consider adding this support.
https://github.com/ethereum-mining/ethminer
That will get most miners using Claymore and non-Claymore miners out there... I think there is no dev fee in ethminer
If X3 cant work with NH, I have little confidence E3 can work....
-
Steve Sokolowski
- Posts: 4585
- Joined: Wed Aug 27, 2014 3:27 pm
- Location: State College, PA
Re: Ehash/claymore rig setup
Do you know if there is a proxy server that can convert between the two protocols? Using the old "getWork" protocol would require a significant amount of time to implement. That way, we could focus on other algorithms, while using proven code for supporting both on Ethash.citronick wrote:Steve said that Nicehash stratum is currently supported - which is -esm 3 Claymore speak.
I think we need get work type mining support like ethminer - perhaps PH can consider adding this support.
https://github.com/ethereum-mining/ethminer
That will get most miners using Claymore and non-Claymore miners out there... I think there is no dev fee in ethminer
If X3 cant work with NH, I have little confidence E3 can work....
-
PolakCrypto
- Posts: 26
- Joined: Tue Jun 26, 2018 10:27 pm
Re: Ehash/claymore rig setup
Whats a "solid" working bat line for ethminer, what im using and keep getting disconnected with?
I just saw your Claymore string above and tried it with -esm 3 and some adjustments and finally got connected. Going to test claymore and see if I get disconnected.
Also does static difficulty d= argument work or is it disallowed for now?
EDIT: I got claymore working but it still disconnects for me after mining for a bit on a static coin(some cards cant handle higher size dag files in my rig so I set a static coin to mine). Then when it reconnects, if it does, it fails to mine cause of the dag size aka it wont reconnect and mine my selected static coin.
Probably just a few bugs to work out yet for EThash. Tried for last hour or so and itll mine for 5 minutes sometimes, 15 minutes, i think my best was 45 minutes then it started acting up/disconnecting.
I just saw your Claymore string above and tried it with -esm 3 and some adjustments and finally got connected. Going to test claymore and see if I get disconnected.
Also does static difficulty d= argument work or is it disallowed for now?
EDIT: I got claymore working but it still disconnects for me after mining for a bit on a static coin(some cards cant handle higher size dag files in my rig so I set a static coin to mine). Then when it reconnects, if it does, it fails to mine cause of the dag size aka it wont reconnect and mine my selected static coin.
Probably just a few bugs to work out yet for EThash. Tried for last hour or so and itll mine for 5 minutes sometimes, 15 minutes, i think my best was 45 minutes then it started acting up/disconnecting.